table of contents
| FENCE_AGENT(8) | System Manager's Manual | FENCE_AGENT(8) |
NAME¶
fence_intelmodular - Fence agent for Intel Modular
DESCRIPTION¶
fence_intelmodular is an I/O Fencing agent which can be used with Intel Modular device (tested on Intel MFSYS25, should work with MFSYS35 as well).
Note: Since firmware update version 2.7, SNMP v2 write support is removed, and replaced by SNMP v3 support. So agent now has default SNMP version 3. If you are using older firmware, please supply -d for command line and snmp_version option for your cluster.conf.
fence_intelmodular accepts options on the command line as well as from stdin. Fenced sends parameters through stdin when it execs the agent. fence_intelmodular can be run by itself with command line options. This is useful for testing and for turning outlets on or off from scripts.
Vendor URL: http://www.intel.com
PARAMETERS¶
- -o, --action=[action]
- Fencing Action (Default Value: reboot)
- -c, --community=[community]
- Set the community string
- -4, --inet4-only
- Forces agent to use IPv4 addresses only
- -6, --inet6-only
- Forces agent to use IPv6 addresses only
- -a, --ip=[ip]
- IP Address or Hostname This parameter is always required.
- -l, --username=[name]
- Login Name
- -p, --password=[password]
- Login password or passphrase
- -S, --password-script=[script]
- Script to retrieve password
- -n, --plug=[id]
- Physical plug number, name of virtual machine or UUID This parameter is always required.
- -b, --snmp-auth-prot=[prot]
- Set authentication protocol (MD5|SHA)
- -P, --snmp-priv-passwd=[pass]
- Set privacy protocol password
- -R, --snmp-priv-passwd-script
- Script to run to retrieve privacy password
- -B, --snmp-priv-prot=[prot]
- Set privacy protocol (DES|AES)
- -E, --snmp-sec-level=[level]
- Set security level (noAuthNoPriv|authNoPriv|authPriv)
- -d, --snmp-version=[version]
- Specifies SNMP version to use (1,2c,3)
- -u, --udpport
- UDP/TCP port to use for connection with device
- -v, --verbose
- Verbose mode
- -D, --debug-file=[debugfile]
- Write debug information to given file
- -V, --version
- Display version information and exit
- -h, --help
- Display help and exit
- -C, --separator=[char]
- Separator for CSV created by operation list (Default Value: ,)
- --delay=[seconds]
- Wait X seconds before fencing is started (Default Value: 0)
- --login-timeout=[seconds]
- Wait X seconds for cmd prompt after login (Default Value: 5)
- --power-timeout=[seconds]
- Test X seconds for status change after ON/OFF (Default Value: 20)
- --power-wait=[seconds]
- Wait X seconds after issuing ON/OFF (Default Value: 0)
- --shell-timeout=[seconds]
- Wait X seconds for cmd prompt after issuing command (Default Value: 3)
- --retry-on=[attempts]
- Count of attempts to retry power on (Default Value: 1)
ACTIONS¶
- on
- Power on machine.
- off
- Power off machine.
- reboot
- Reboot machine.
- status
- This returns the status of the plug/virtual machine.
- list
- List available plugs with aliases/virtual machines if there is support for more then one device. Returns N/A otherwise.
- list-status
- List available plugs with aliases/virtual machines and their power state if it can be obtained without additional commands.
- monitor
- Check the health of fence device
- metadata
- Display the XML metadata describing this resource.
STDIN PARAMETERS¶
- action
- Fencing Action (Default Value: reboot)
- community
- Set the community string
- inet4_only
- Forces agent to use IPv4 addresses only
- inet6_only
- Forces agent to use IPv6 addresses only
- ipaddr
- IP Address or Hostname This parameter is always required.
- login
- Login Name
- passwd
- Login password or passphrase
- passwd_script
- Script to retrieve password
- port
- Physical plug number, name of virtual machine or UUID This parameter is always required.
- snmp_auth_prot
- Set authentication protocol (MD5|SHA)
- snmp_priv_passwd
- Set privacy protocol password
- snmp_priv_passwd_script
- Script to run to retrieve privacy password
- snmp_priv_prot
- Set privacy protocol (DES|AES)
- snmp_sec_level
- Set security level (noAuthNoPriv|authNoPriv|authPriv)
- snmp_version
- Specifies SNMP version to use (1,2c,3)
- udpport
- UDP/TCP port to use for connection with device
- verbose
- Verbose mode
- debug
- Write debug information to given file
- version
- Display version information and exit
- help
- Display help and exit
- separator
- Separator for CSV created by operation list (Default Value: ,)
- delay
- Wait X seconds before fencing is started (Default Value: 0)
- login_timeout
- Wait X seconds for cmd prompt after login (Default Value: 5)
- power_timeout
- Test X seconds for status change after ON/OFF (Default Value: 20)
- power_wait
- Wait X seconds after issuing ON/OFF (Default Value: 0)
- shell_timeout
- Wait X seconds for cmd prompt after issuing command (Default Value: 3)
- retry_on
- Count of attempts to retry power on (Default Value: 1)
| 2009-10-20 | fence_intelmodular (Fence Agent) |