2. EL 6 ELS
  3. btrfs-progs
  4. btrfs(8)

Scroll to navigation

BTRFS(8) btrfs BTRFS(8)

NAME

btrfs - control a btrfs filesystem

SYNOPSIS

btrfs subvolume snapshot [-r] <source> [<dest>/]<name>

btrfs subvolume delete <subvolume> [<subvolume>...]

btrfs subvolume create [<dest>/]<name>

btrfs subvolume list [-aprts] [-g [+|-]value] [-c [+|-]value] [--rootid=rootid,gen,ogen,path] <path>

btrfs subvolume set-default <id> <path>

btrfs subvolume get-default <path>

btrfs filesystem defragment -c[zlib|lzo] [-l len] [-s start] [-t size] -[vf] <file>|<dir> [<file>|<dir>...]

btrfs filesystem sync <path>

btrfs filesystem resize [devid:][+/-]<size>[gkm]|[devid:]max <filesystem>

btrfs filesystem label <dev> [newlabel]

btrfs subvolume find-new <subvolume> <last_gen>

btrfs filesystem balance <path>

btrfs device scan [--all-devices|<device> [<device>...]]

btrfs device show [--all-devices|<uuid>|<label>]

btrfs device add <device> [<device>...] <path>

btrfs device delete <device> [<device>...] <path>

btrfs scrub start [-Bdqru] {<path>|<device>}

btrfs scrub cancel {<path>|<device>}

btrfs scrub resume [-Bdqru] {<path>|<device>}

btrfs scrub status [-d] {<path>|<device>}

btrfs inspect-internal inode-resolve [-v] <inode> <path>

btrfs inspect-internal logical-resolve [-Pv] [-s size] <logical> <path>

btrfs help|--help|-h

btrfs <command> --help

DESCRIPTION

btrfs is used to control the filesystem and the files and directories stored. It is the tool to create or destroy a snapshot or a subvolume for the filesystem, to defrag a file or a directory, flush the data to the disk, to resize the filesystem, to scan the device.

It is possible to abbreviate the commands unless the commands are ambiguous. For example: it is possible to run btrfs sub snaps instead of btrfs subvolume snapshot. But btrfs file s is not allowed, because file s may be interpreted both as filesystem show and as filesystem sync. In this case btrfs returns filesystem sync If a command is terminated by --help , the detailed help is showed. If the passed command matches more commands, detailed help of all the matched commands is showed. For example btrfs dev --help shows the help of all device* commands.

COMMANDS

Create a writable/readonly snapshot of the subvolume <source> with the name <name> in the <dest> directory. If <source> is not a subvolume, btrfs returns an error. If -r is given, the snapshot will be readonly.
Delete the subvolume <subvolume>. If <subvolume> is not a subvolume, btrfs returns an error.
Create a subvolume in <dest> (or in the current directory if <dest> is omitted).
List the subvolumes present in the filesystem <path>. For every subvolume the following information is shown by default. ID <ID> top level <ID> path <path> where path is the relative path of the subvolume to the top level subvolume.

The subvolume's ID may be used by the subvolume set-default command, or at mount time via the subvol= option. If -p is given, then parent <ID> is added to the output between ID and top level. The parent's ID may be used at mount time via the subvolrootid= option.

-t print the result as a table.

-a print all the subvolumes in the filesystem.

-r only readonly subvolumes in the filesystem wille be listed.

-s only snapshot subvolumes in the filesystem will be listed.

-g [+|-]value list subvolumes in the filesystem that its generation is >=, <= or = value. '+' means >= value, '-' means <= value, If there is neither '+' nor '-', it means = value.

-c [+|-]value list subvolumes in the filesystem that its ogeneration is >=, <= or = value. The usage is the same to '-g' option.

--sort=gen,ogen,path,rootid list subvolumes in order by specified items. you can add '+' or '-' in front of each items, '+' means ascending,'-' means descending. The default is ascending.

for --sort you can combine some items together by ',', just like -sort=+ogen,-gen,path,rootid.

Set the subvolume of the filesystem <path> which is mounted as default. The subvolume is identified by <id>, which is returned by the subvolume list command.
Get the default subvolume of the filesystem <path>. The output format is similar to subvolume list command.

Defragment file data and/or directory metadata. To defragment all files in a directory you have to specify each one on its own or use your shell wildcards.

The start position and the number of bytes to defragment can be specified by start and len. Any extent bigger than threshold will be considered already defragged. Use 0 to take the kernel default, and use 1 to say every single extent must be rewritten. You can also turn on compression in defragment operations.

-v be verbose

-c compress file contents while defragmenting

-f flush filesystem after defragmenting

-s start defragment only from byte start onward

-l len defragment only up to len bytes

-t size defragment only files at least size bytes big

NOTE: defragmenting with kernels up to 2.6.37 will unlink COW-ed copies of data, don't use it if you use snapshots, have de-duplicated your data or made copies with cp --reflink.

List the recently modified files in a subvolume, after <last_gen> ID.
Force a sync for the filesystem identified by <path>.
Resize a filesystem identified by <path> for the underlying device devid. The devid can be found with btrfs filesystem show and defaults to 1 if not specified. The <size> parameter specifies the new size of the filesystem. If the prefix + or - is present the size is increased or decreased by the quantity <size>. If no units are specified, the unit of the <size> parameter defaults to bytes. Optionally, the size parameter may be suffixed by one of the following units designators: 'K', 'M', or 'G', kilobytes, megabytes, or gigabytes, respectively.

If 'max' is passed, the filesystem will occupy all available space on the device devid.

The resize command does not manipulate the size of underlying partition. If you wish to enlarge/reduce a filesystem, you must make sure you can expand the partition before enlarging the filesystem and shrink the partition after reducing the size of the filesystem. This can done using fdisk(8) or parted(8) to delete the existing partition and recreate it with the new desired size. When recreating the partition make sure to use the same starting disk cylinder as before.

Show or update the label of a filesystem. <dev> is used to identify the filesystem. If a newlabel optional argument is passed, the label is changed. The following constraints exist for a label:
- the maximum allowable length shall be less or equal than 256 chars
- the label shall not contain the '/' or '\' characters.

NOTE: Currently there are the following limitations:

- the filesystem has to be unmounted
- the filesystem should not have more than one device.
Show the btrfs filesystem with some additional info. If no UUID or label is passed, btrfs show info of all the btrfs filesystem. If --all-devices is passed, all the devices under /dev are scanned; otherwise the devices list is extracted from the /proc/partitions file.
Balance the chunks of the filesystem identified by <path> across the devices.
Add device(s) to the filesystem identified by <path>.
Remove device(s) from a filesystem identified by <path>.
If one or more devices are passed, these are scanned for a btrfs filesystem. If no devices are passed, btrfs scans all the block devices listed in the /proc/partitions file. Finally, if --all-devices is passed, all the devices under /dev are scanned.
Start a scrub on all devices of the filesystem identified by <path> or on a single <device>. Without options, scrub is started as a background process. Progress can be obtained with the scrub status command. Scrubbing involves reading all data from all disks and verifying checksums. Errors are corrected along the way if possible.

Options

Do not background and print scrub statistics when finished.
Print separate statistics for each device of the filesystem (-B only).
Quiet. Omit error messages and statistics.
Read only mode. Do not attempt to correct anything.
Scrub unused space as well. (NOT IMPLEMENTED)
If a scrub is running on the filesystem identified by <path>, cancel it. Progress is saved in the scrub progress file and scrubbing can be resumed later using the scrub resume command. If a <device> is given, the corresponding filesystem is found and scrub cancel behaves as if it was called on that filesystem.
Resume a canceled or interrupted scrub cycle on the filesystem identified by <path> or on a given <device>. Does not start a new scrub if the last scrub finished successfully.

Options

Show status of a running scrub for the filesystem identified by <path> or for the specified <device>. If no scrub is running, show statistics of the last finished or canceled scrub for that filesystem or device.

Options

Print separate statistics for each device of the filesystem.
Resolves an <inode> in subvolume <path> to all filesystem paths.

Options

verbose mode. print count of returned paths and ioctl() return value
Resolves a <logical> address in the filesystem mounted at <path> to all inodes. By default, each inode is then resolved to a file system path (similar to the inode-resolve subcommand).

Options

skip the path resolving and print the inodes instead
verbose mode. print count of returned paths and all ioctl() return values
set inode container's size. This is used to increase inode container's size in case it is not enough to read all the resolved results. The max value one can set is 64k.

EXIT STATUS

btrfs returns a zero exist status if it succeeds. Non zero is returned in case of failure.

AVAILABILITY

btrfs is part of btrfs-progs. Btrfs filesystem is currently under heavy development, and not suitable for any uses other than benchmarking and review. Please refer to the btrfs wiki http://btrfs.wiki.kernel.org for further details.

SEE ALSO

mkfs.btrfs(8)

btrfs