NAME¶

nvmetcli - Configure NVMe-over-Fabrics Target.

USAGE¶

nvmetcli
nvmetcli clear
nvmetcli restore [filename.json]

DESCRIPTION¶

nvmetcli is a program used for viewing, editing, saving, and starting a Linux kernel NVMe Target, used for an NVMe-over-Fabrics network configuration. It allows an administrator to export a storage resource (such as NVMe devices, files, and volumes) to a local block device and expose them to remote systems based on the NVMe-over-Fabrics specification from http://www.nvmexpress.org.

nvmetcli is run as root and has two modes:

BACKGROUND¶

The term NQN used throughout this man page is the NVMe Qualified Name format which an NVMe endpoint (device, subsystem, etc) must follow to guarantee a unique name under the NVMe standard. Any name in a network system setup can be used, but if it does not follow the NQN format, it may not be unique on an NVMe-over-Fabrics network.

Note that some of the fields set for an NVMe Target port under interactive mode are defined in the "Discovery Log Page" section of NVMe-over-Fabrics specification. Each NVMe Target has a discovery controller mechanism that an NVMe Host can use to determine the NVM subsystems it can access. nvmetcli can be used to add a new record to the discovery controller upon each new subsystem entry and port entry that the newly created subsystem entry binds to (see OPTIONS and EXAMPLES sections). Each NVMe Host only gets to see the discovery entries defined in /subsystems/[NQN NAME]/allowed_hosts and the IP port it is connected to the NVMe Target. An NVMe Host can retrieve these discovery logs via the nvme-cli tool (https://github.com/linux-nvme/nvme-cli).

OPTIONS¶

Interactive Configuration Shell

To start the interactive configuration shell, type nvmetcli on the command-line. nvmetcli interacts with the Linux kernel NVMe Target configfs subsystem starting at base nvmetcli directories /port, /subsystem, and /host. Configuration changes entered by the administrator are made immediately to the kernel target configuration. The following commands can be used while in the interactive configuration shell mode:

Command Line Mode

Typing nvmetcli [cmd] on the command-line will execute a command and not enter the interactive configuration shell.

EXAMPLES¶

Make sure to run nvmetcli as root, the nvmet module is loaded, your devices and all dependent modules are loaded, and configfs is mounted on /sys/kernel/config using:

mount -t configs none /sys/kernel/config

The following section walks through a configuration example.

# ./nvmetcli
...>

> cd /subsystems
...> create testnqn

...> cd /hosts
...> create hostnqn
...> cd /subsystems/testnqn
...> set attr allow_any_host=0
...> cd /subsystems/testnqn/allowed_hosts/
...> create hostnqn

...> cd /subsystems/testnqn/allowed_hosts/
...> delete hostnqn

...> cd /subsystems/testnqn/
...> set attr allow_any_host=1

...> cd /subsystems/testnqn/namespaces
...> create 1
...> cd 1
...> set device path=/dev/nvme0n1
...> enable

Note that in the above setup the device_nguid attribute does not have to be set for correct NVMe Target functionality (but to correctly match a namespace to the exact device upon clear and restore operations, it is advised to set the device_nguid parameter).

...> cd /ports/
...> create 1
...> cd 1/
...> set addr trtype=loop
...> cd subsystems/
...> create testnqn

...> cd /ports/
...> create 2
...> cd 2/
...> set addr trtype=rdma
...> set addr adrfam=ipv4
...> set addr traddr=192.168.6.68
...> set addr trsvcid=4420
...> cd subsystems/
...> create testnqn

...> cd /ports/
...> create 3
...> cd 3/
...> set addr trtype=fc
...> set addr adrfam=fc
...> set addr traddr=nn-0x1000000044001123:pn-0x2000000055001123
...> set addr trsvcid=none
...> cd subsystems/
...> create testnqn

./nvmetcli
...> saveconfig test.json

  ./nvmetcli restore test.json

  ./nvmetcli clear

ADDITIONAL INFORMATION¶

nvmetcli has the ability to start and stop the NVMe Target configuration on boot and shutdown through the systemctl Linux utility via a .service file. nvmetcli package comes with nvmet.service which when installed, it can automatically restore the default, saved NVMe Target configuration from /etc/nvmet/config.json. nvmet.service can be installed in directories such as /lib/systemd/system.

To explicitly enable the service, type:

  systemctl enable nvmet

To explicitly disable the service, type:

  systemctl disable nvmet

See also systemctl(1).

AUTHORS¶

This man page was written by Jay Freyensee[1]. nvmetcli was originally written by Christoph Hellwig[2].

REPORTING BUGS & DEVELOPMENT¶

Please send patches and bug reports to linux-nvme@lists.infradead.org[3] for review and acceptance.

LICENSE¶

nvmetcli is licensed under the Apache License, Version 2.0. Software distributed under this license is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either expressed or implied.

NOTES¶

1.

Jay Freyensee

2.

Christoph Hellwig

3.

linux-nvme@lists.infradead.org