This name is set based on the ordering information given by the firmware for on-board devices. The name consists of the prefix, letter o, and a number specified by the firmware. This is only available for PCI devices.

This property is set based on label given by the firmware for on-board devices. The name consists of the prefix concatenated with the label. This is only available for PCI devices.

This name consists of the prefix, letter x, and 12 hexadecimal digits of the MAC address. It is available if the device has a fixed MAC address. Because this name is based on an attribute of the card itself, it remains "stable" when the device is moved (even between machines), but will change when the hardware is replaced.

This property describes the slot position. Different schemes are used depending on the bus type, as described in the table below. In all cases, PCI slot information must be known. In case of USB, BCMA, and SR-VIO devices, the full name consists of the prefix, PCI slot identifier, and USB or BCMA or SR-VIO slot identifier. The first two parts are denoted as "..." in the table below.

Table 2. Slot naming schemes

Format	Description
prefix [Pdomain] sslot [ffunction] [nport_name | ddev_port]	PCI slot number
... bnumber	Broadcom bus (BCMA) core number
... uport... [cconfig] [iinterface]	USB port number chain
... vslot	SR-VIO slot number

The PCI domain is only prepended when it is not 0. All multi-function PCI devices will carry the
ffunction number in the device name, including the function 0 device. For non-multi-function devices, the number is suppressed if 0. The port name port_name is used, or the port number ddev_port if the name is not known.

For BCMA devices, the core number is suppressed when 0.

For USB devices the full chain of port numbers of hubs is composed. If the name gets longer than the maximum number of 15 characters, the name is not exported. The usual USB configuration number 1 and interface number 0 values are suppressed.

SR-IOV virtual devices are named based on the name of the parent interface, with a suffix of v and the virtual device number, with any leading zeros removed. The bus number is ignored.

In some configurations a parent PCI bridge of a given network controller may be associated with a slot. In such case we don't generate this device property to avoid possible naming conflicts.

This property describes the device installation location. Different schemes are used depending on the bus type, as described in the table below. For BCMA and USB devices, PCI path information must known, and the full name consists of the prefix, PCI slot identifier, and USB or BCMA location. The first two parts are denoted as "..." in the table below.

Table 3. Path naming schemes

Format	Description
prefix cbus_id	CCW or grouped CCW device identifier
prefix avendor model iinstance	ACPI path names for ARM64 platform devices
prefix [Pdomain] pbus sslot [ffunction] [nphys_port_name | ddev_port]	PCI geographical location
... bnumber	Broadcom bus (BCMA) core number
... uport... [cconfig] [iinterface]	USB port number chain

CCW and grouped CCW devices are found in IBM System Z mainframes. Any leading zeros and dots are suppressed.

For PCI, BCMA, and USB devices, the same rules as described above for slot naming are used.

Naming was changed for virtual network interfaces created with SR-IOV and NPAR and for devices where the PCI network controller device does not have a slot number associated.

SR-IOV virtual devices are named based on the name of the parent interface, with a suffix of "vport", where port is the virtual device number. Previously those virtual devices were named as if completely independent.

The ninth and later NPAR virtual devices are named following the scheme used for the first eight NPAR partitions. Previously those devices were not renamed and the kernel default ("ethN") was used.

Names are also generated for PCI devices where the PCI network controller device does not have an associated slot number itself, but one of its parents does. Previously those devices were not renamed and the kernel default was used.

Same as naming scheme rhel-8.0.

Same as naming scheme rhel-8.0.

Same as naming scheme rhel-8.0.

If the PCI slot is assocated with PCI bridge and that has multiple child network controllers then all of them might derive the same value of ID_NET_NAME_SLOT property. That could cause naming conflict if the property is selected as a device name. Now, we detect the situation, slot - bridge relation, and we don't produce the ID_NET_NAME_SLOT property to avoid possible naming conflict.

Same as naming scheme rhel-8.4.

Same as naming scheme rhel-8.4.

PCI hotplug slot names for the s390 PCI driver are a hexadecimal representation of the function_id device attribute. This attribute is now used to build the ID_NET_NAME_SLOT. Before that, all slot names were parsed as decimal numbers, which could either result in an incorrect value of the ID_NET_NAME_SLOT property or none at all.

Some firmware and hypervisor implementations report unreasonable high numbers for the onboard index. To prevent the generation of bogus onbard interface names, index numbers greater than 16381 (2^14-1) were ignored. For s390 PCI devices index values up to 65535 (2^16-1) are valid. To account for that, the limit is increased to now 65535.

Same as naming scheme rhel-8.7.

$ udevadm test-builtin net_id /sys/class/net/enp0s31f6
...
Using default interface naming scheme 'rhel-8.3'.
ID_NET_NAMING_SCHEME=rhel-8.3
ID_NET_NAME_MAC=enx54ee75cb1dc0
ID_OUI_FROM_DATABASE=Wistron InfoComm(Kunshan)Co.,Ltd.
ID_NET_NAME_PATH=enp0s31f6
...

ID_NET_NAME_ONBOARD=eno1
ID_NET_NAME_ONBOARD_LABEL=enEthernet Port 1


      

# /sys/devices/pci0000:00/0000:00:1c.3/0000:05:00.0/net/ens1
ID_NET_NAME_MAC=enx000000000466
ID_NET_NAME_PATH=enp5s0
ID_NET_NAME_SLOT=ens1

# /sys/devices/pci0000:00/0000:00:1c.0/0000:02:00.0/net/enp2s0f0
ID_NET_NAME_MAC=enx78e7d1ea46da
ID_NET_NAME_PATH=enp2s0f0
# /sys/devices/pci0000:00/0000:00:1c.0/0000:02:00.1/net/enp2s0f1
ID_NET_NAME_MAC=enx78e7d1ea46dc
ID_NET_NAME_PATH=enp2s0f1

# /sys/devices/pci0000:00/0000:00:1c.1/0000:03:00.0/net/wlp3s0
ID_NET_NAME_MAC=wlx0024d7e31130
ID_NET_NAME_PATH=wlp3s0

# /sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4/2-1.4:1.6/net/wwp0s29u1u4i6
ID_NET_NAME_MAC=wwx028037ec0200
ID_NET_NAME_PATH=wwp0s29u1u4i6

# /sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0/net/enp0s29u1u2
ID_NET_NAME_MAC=enxd626b3450fb5
ID_NET_NAME_PATH=enp0s29u1u2

# /sys/devices/css0/0.0.0007/0.0.f5f0/group_device/net/encf5f0
ID_NET_NAME_MAC=enx026d3c00000a
ID_NET_NAME_PATH=encf5f0