table of contents
Pnmpad User Manual(0) | Pnmpad User Manual(0) |
NAME¶
pnmpad - add borders to a PNM image
SYNOPSIS¶
pnmpad [-white|-black] [-width=pixels] [-halign=ratio] [-mwidth=pixels] [-left=pixels] [-right=pixels] [-height=pixels] [-valign=ratio] [-mheight=pixels] [-top=pixels] [-bottom=pixels] [-reportonly] [-verbose] [pnmfile]
DESCRIPTION¶
This program is part of Netpbm(1).
pnmpad reads a PNM image as input and outputs a PNM image that is the input image plus black or white borders of the sizes specified.
If you just need to convert an image to a certain size regardless of the original dimensions, pamcut with the -pad option may be a better choice.
pnmmargin does essentially the same thing, but allows you to add borders of any color and requires all four borders to be the same size.
You can use pamcomp to add borders of any content - solid
color,
pattern, or whatever. For example, if you wanted to add 10 pixels of red
borders to the top and bottom of a 100x100 image, you could create a
100x120 red image (e.g. with ppmmake) and then use pamcomp
to insert your 100x100 image into the center of it.
OPTIONS¶
In addition to the options common to all programs based on
libnetpbm (most notably -quiet, see
Common Options ), pnmpad recognizes the following command line
options:
All options can be abbreviated to their shortest unique prefix. You may use two hyphens instead of one to designate an option. You may use either white space or an equals sign between an option name and its value.
- -white
- -black
- Set pad color. Default is -black.
- -left=pixels
- -right=pixels
- -width=width
- -halign=ratio
- -mwidth=pixels
- Specify amount of left and right padding in pixels.
-left and -right directly specify the amount of padding added to the left and right sides, respectively, of the image.
Alternatively, you can specify -width and just one of -left and -right and pnmpad calculates the required padding on the other side to make the output width pixels wide. If the -width value is less than the width of the input image plus the specified padding, pnmpad ignores -width.
If you specify all three of -width, -left, and -right, you must ensure that the -left and -right padding are sufficient to make the image at least as wide as -width specifies. Otherwise, pnmpad fails.
When you specify -width without -left or -right, and -width is larger than the input image, pnmpad chooses left and right padding amounts in a certain ratio. That ratio defaults to half, but you can set it to anything (from 0 to 1) with the -halign option. If the input image is already at least as wide as -width specifies, pnmpad adds no padding.
Common values for -halign are:
- 0.0
- left aligned
- 0.5
- center aligned (default)
- 1.0
- right aligned
-mwidth=pixels says to pad to a multiple of pixels pixels. E.g. if pixels is 10, the output image width will be a multiple of 10 pixels. pnmpad adds to whatever padding the other options say to do to get to this multiple. It divides that padding between the left and right sides of the image to maintain the ratio the other options produce. E.g. if you say -left=10 -right=10 -mwidth=50 with a 100-pixel image, you end up with a 150-pixel image with the extra padding split evenly between left and right for a total of 25 pixels of padding on the left and 25 on the right.
Before Netpbm 10.23 (July 2004), pnmpad did not allow the -left or -right option together with -width.
Before Netpbm 10.72 (September 2015), there is no -mwidth.
- -top=pixels
- -bottom=pixels
- -height=height
- -valign=ratio
- -mheight=pixels
- These options determine the vertical padding. They are analogous to the horizontal padding options above.
- -reportonly
-
This causes pnmpad to write to Standard Output a description of the
padding it would have done instead of producing an output image. Seebelow for a description of this output and ways
to use it.This option was new in Netpbm 10.89 (December 2019).
- -verbose
- This causes verbose messages.
REPORT ONLY¶
When you specify -reportonly, pnmpad does not
produce an
output image. Instead, it writes to Standard Output a description of the
padding it would have done without -reportonly.
That description is one line of text, containing 6 decimal numbers
of
pixels, separated by spaces:
- left padding
- right padding
- top padding
- bottom padding
- output width
- output height
Example:
4 3 0 2 100 100
One use for this is to make padding which is fancier than the
black and
white that pnmpad can do.
In the following example, we pad an image with 10 pixels of gray
all
around, without knowing the original image dimensions beforehand. We do
this by generating a gray image with pbmmake and then pasting the
subject image into the middle of it.
The example uses shell arrays, such as exist in Bash, but not Dash.
pad=($(pnmpad -reportonly -left=10 -right=10 -top=10 -bottom=10 input.ppm))
pbmmake -gray ${pad[4]} ${pad[5]} | \
pnmpaste input.ppm ${pad[0]} ${pad[2]} -
HISTORY¶
Before February 2002, pnmpad had a different option syntax which was less expressive and not like conventional Netpbm programs. That syntax is still understood by pnmpad for backward compatibility, but not documented or supported for future use.
SEE ALSO¶
pbmmake(1), pnmpaste(1), pamcut(1), pnmcrop(1), pamcomp(1), pnmmargin(1), pbm(1)
AUTHOR¶
Copyright (C) 2002 by Martin van Beilen
Copyright (C) 1990 by Angus Duggan
Copyright (C) 1989 by Jef Poskanzer.
Permission to use, copy, modify, and distribute this software and its documentation for any purpose and without fee is hereby granted, provided that the above copyright notice appear in all copies and that both that copyright notice and this permission notice appear in supporting documentation. This software is provided "as is" without express or implied warranty.
DOCUMENT SOURCE¶
This manual page was generated by the Netpbm tool 'makeman' from HTML source. The master documentation is at
05 October 2019 | netpbm documentation |