This name is set based on the numeric ordering information given by the firmware for on-board devices. Different schemes are used depending on the firmware type, as described in the table below.

Table 2. Onboard naming schemes

Format	Description
prefixonumber	PCI onboard index
prefixdnumber	Devicetree alias index

This property is set based on textual label given by the firmware for on-board devices. The name consists of the prefix concatenated with the label. This is only available for PCI devices.

This name consists of the prefix, letter x, and 12 hexadecimal digits of the MAC address. It is available if the device has a fixed MAC address. Because this name is based on an attribute of the card itself, it remains "stable" when the device is moved (even between machines), but will change when the hardware is replaced.

This property describes the slot position. Different schemes are used depending on the bus type, as described in the table below. In case of USB, BCMA, and SR-VIO devices, the full name consists of the prefix, PCI slot identifier, and USB or BCMA or SR-VIO slot identifier. The first two parts are denoted as "..." in the table below.

Table 3. Slot naming schemes

Format	Description
prefix [Pdomain] sslot [ffunction] [nport_name | ddev_port]	PCI slot number
prefix vslot	VIO slot number (IBM PowerVM)
prefix Xnumber	VIF interface number (Xen)
... bnumber	Broadcom bus (BCMA) core number
... uport... [cconfig] [iinterface]	USB port number chain
... vslot	SR-VIO slot number
... rslot	SR-IOV slot number

The PCI domain is only prepended when it is not 0. All multi-function PCI devices will carry the
ffunction number in the device name, including the function 0 device. For non-multi-function devices, the number is suppressed if 0. The port name port_name is used, or the port number ddev_port if the name is not known.

For BCMA devices, the core number is suppressed when 0.

For USB devices the full chain of port numbers of hubs is composed. If the name gets longer than the maximum number of 15 characters, the name is not exported. The usual USB configuration number 1 and interface number 0 values are suppressed.

SR-IOV virtual devices are named based on the name of the parent interface, with a suffix of v and the virtual device number, with any leading zeros removed. The bus number is ignored.

SR-IOV virtual device representors are named based on the name of the physical device interface, with a suffix of r and the number of the virtual device that is linked to the particular representor, with any leading zeros removed. The physical port name and the bus number are ignored.

In some configurations a parent PCI bridge of a given network controller may be associated with a slot. In such case we don't generate this device property to avoid possible naming conflicts.

This property describes the device installation location. Different schemes are used depending on the bus type, as described in the table below. For BCMA and USB devices, PCI path information must known, and the full name consists of the prefix, PCI slot identifier, and USB or BCMA location. The first two parts are denoted as "..." in the table below.

Table 4. Path naming schemes

Format	Description
prefix cbus_id	CCW or grouped CCW device identifier
prefix avendor model iinstance	ACPI path names for ARM64 platform devices
prefix iaddress nport_name	Netdevsim (simulated networking device) device number and port name
prefix [Pdomain] pbus sslot [ffunction] [nphys_port_name | ddev_port]	PCI geographical location
... bnumber	Broadcom bus (BCMA) core number
... uport... [cconfig] [iinterface]	USB port number chain

CCW and grouped CCW devices are found in IBM System Z mainframes. Any leading zeros and dots are suppressed.

For PCI, BCMA, and USB devices, the same rules as described above for slot naming are used.

This is the naming scheme that was implemented in systemd 238.

Naming was changed for virtual network interfaces created with SR-IOV and NPAR and for devices where the PCI network controller device does not have a slot number associated.

SR-IOV virtual devices are named based on the name of the parent interface, with a suffix of "vport", where port is the virtual device number. Previously those virtual devices were named as if completely independent.

The ninth and later NPAR virtual devices are named following the scheme used for the first eight NPAR partitions. Previously those devices were not renamed and the kernel default ("ethN") was used.

Names are also generated for PCI devices where the PCI network controller device does not have an associated slot number itself, but one of its parents does. Previously those devices were not renamed and the kernel default was used.

The "ib" prefix and stable names for infiniband devices are introduced. Previously those devices were not renamed.

The ACPI index field (used in ID_NET_NAME_ONBOARD=) is now also used when 0.

A new naming policy NamePolicy=keep was introduced. With this policy, if the network device name was already set by userspace, the device will not be renamed again. Previously, this naming policy applied implicitly, and now it must be explicitly requested. Effectively, this means that network devices will be renamed according to the configuration, even if they have been renamed already, if keep is not specified as the naming policy in the .link file. See systemd.link(5) for a description of NamePolicy=.

MACAddressPolicy=persistent was extended to set MAC addresses based on the device name. Previously addresses were only based on the ID_NET_NAME_* attributes, which meant that interface names would never be generated for virtual devices. Now a persistent address will be generated for most devices, including in particular bridges.

Note: when userspace does not set a MAC address for a bridge device, the kernel will initially assign a random address, and then change it when the first device is enslaved to the bridge. With this naming policy change, bridges get a persistent MAC address based on the bridge name instead of the first enslaved device.

Support for renaming netdevsim (simulated networking) devices was added. Previously those devices were not renamed.

Previously two-letter interface type prefix was prepended to ID_NET_LABEL_ONBOARD=. This is not done anymore.

When systemd-nspawn(1) derives the name for the host side of the network interface created with --network-veth from the container name it previously simply truncated the result at 15 characters if longer (since that's the maximum length for network interface names). From now on, for any interface name that would be longer than 15 characters the last 4 characters are set to a 24bit hash value of the full interface name. This way network interface name collisions between multiple similarly named containers (who only differ in container name suffix) should be less likely (but still possible, since the 24bit hash value is very small).

When a PCI slot is associated with a PCI bridge that has multiple child network controllers, the same value of the ID_NET_NAME_SLOT property might be derived for those controllers. This would cause a naming conflict if the property is selected as the device name. Now, we detect this situation and don't produce the ID_NET_NAME_SLOT property.

PCI hotplug slot names for the s390 PCI driver are a hexadecimal representation of the function_id device attribute. This attribute is now used to build the ID_NET_NAME_SLOT. Before that, all slot names were parsed as decimal numbers, which could either result in an incorrect value of the ID_NET_NAME_SLOT property or none at all.

Some firmware and hypervisor implementations report unreasonably high numbers for the onboard index. To prevent the generation of bogus onbard interface names, index numbers greater than 16381 (2¹⁴-1) were ignored. For s390 PCI devices index values up to 65535 (2¹⁶-1) are valid. To account for that, the limit was increased to 65535.

The udev rule NAME= replaces ":", "/", and "%" with an underscore ("_"), and refuses strings which contain only numerics.

Added naming scheme for Xen netfront "vif" interfaces based on the guest side VIF number set from the Xen config (or the interface index in AWS EC2).

Since version v247 we no longer set ID_NET_NAME_SLOT if we detect that a PCI device associated with a slot is a PCI bridge as that would create naming conflict when there are more child devices on that bridge. Now, this is relaxed and we will use slot information to generate the name based on it but only if the PCI device has multiple functions. This is safe because distinct function number is a part of the device name for multifunction devices.

Added naming scheme for platform devices with devicetree aliases.

Since version v247 we no longer set ID_NET_NAME_SLOT if we detect that a PCI device associated with a slot is a PCI bridge as that would create naming conflict when there are more child devices on that bridge. Now, this is relaxed and we will use slot information to generate the name based on it but only if the PCI device has multiple functions. This is safe because distinct function number is a part of the device name for multifunction devices.

Same as naming scheme rhel-9.0.

Same as naming scheme rhel-9.0.

Naming was changed for SR-IOV virtual device representors.

The "rslot" suffix was added to differentiate SR-IOV virtual device representors attached to a single physical device interface.

Same as naming scheme rhel-9.3.

This udev property sets a fallback policy for reading a sysfs attribute. If set to 0 udev will not read any sysfs attribute by default, unless it is explicitly allowlisted, see below. If set to 1 udev can use any sysfs attribute unless it is explicitly forbidden. The default value is 1.

This udev property explicitly states if udev shall use the specified sysfsattr, when composing the device name.

$ udevadm test-builtin net_id /sys/class/net/enp0s31f6
...
Using default interface naming scheme 'v243'.
ID_NET_NAMING_SCHEME=v243
ID_NET_NAME_MAC=enx54ee75cb1dc0
ID_OUI_FROM_DATABASE=Wistron InfoComm(Kunshan)Co.,Ltd.
ID_NET_NAME_PATH=enp0s31f6
...

ID_NET_NAME_ONBOARD=eno1
ID_NET_NAME_ONBOARD_LABEL=Ethernet Port 1


      

# /sys/devices/pci0000:00/0000:00:1c.3/0000:05:00.0/net/ens1
ID_NET_NAME_MAC=enx000000000466
ID_NET_NAME_PATH=enp5s0
ID_NET_NAME_SLOT=ens1

# /sys/devices/pci0000:00/0000:00:1c.0/0000:02:00.0/net/enp2s0f0
ID_NET_NAME_MAC=enx78e7d1ea46da
ID_NET_NAME_PATH=enp2s0f0
# /sys/devices/pci0000:00/0000:00:1c.0/0000:02:00.1/net/enp2s0f1
ID_NET_NAME_MAC=enx78e7d1ea46dc
ID_NET_NAME_PATH=enp2s0f1

# /sys/devices/pci0000:00/0000:00:1c.1/0000:03:00.0/net/wlp3s0
ID_NET_NAME_MAC=wlx0024d7e31130
ID_NET_NAME_PATH=wlp3s0

# /sys/devices/pci0000:00/0000:00:03.0/0000:15:00.0/net/ibp21s0f0
ID_NET_NAME_PATH=ibp21s0f0
# /sys/devices/pci0000:00/0000:00:03.0/0000:15:00.1/net/ibp21s0f1
ID_NET_NAME_PATH=ibp21s0f1

# /sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4/2-1.4:1.6/net/wwp0s29u1u4i6
ID_NET_NAME_MAC=wwx028037ec0200
ID_NET_NAME_PATH=wwp0s29u1u4i6

# /sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0/net/enp0s29u1u2
ID_NET_NAME_MAC=enxd626b3450fb5
ID_NET_NAME_PATH=enp0s29u1u2

# /sys/devices/css0/0.0.0007/0.0.f5f0/group_device/net/encf5f0
ID_NET_NAME_MAC=enx026d3c00000a
ID_NET_NAME_PATH=encf5f0

/etc/udev/hwdb.d/50-net-naming-allowlist.hwdb
net:naming:drvirtio_net:*


  ID_NET_NAME_ALLOW=0


  ID_NET_NAME_ALLOW_ACPI_INDEX=1


  ID_NET_NAME_ALLOW_ADDR_ASSIGN_TYPE=1


  ID_NET_NAME_ALLOW_ADDRESS=1


  ID_NET_NAME_ALLOW_ARI_ENABLED=1


  ID_NET_NAME_ALLOW_DEV_PORT=1


  ID_NET_NAME_ALLOW_FUNCTION_ID=1


  ID_NET_NAME_ALLOW_IFLINK=1


  ID_NET_NAME_ALLOW_INDEX=1


  ID_NET_NAME_ALLOW_LABEL=1


  ID_NET_NAME_ALLOW_PHYS_PORT_NAME=1


  ID_NET_NAME_ALLOW_TYPE=1

/etc/udev/hwdb.d/50-net-naming-denylist.hwdb
net:naming:drvirtio_net:*


  ID_NET_NAME_ALLOW=1


  ID_NET_NAME_ALLOW_DEV_PORT=0


  ID_NET_NAME_ALLOW_PHYS_PORT_NAME=0